BARRA OF FUN

WARICK MELDRUM GLEEFULLY INFURIATES THE PURISTS BY BLENDING HIS CHILDHOOD-DREAM CAMARO WITH PROVEN TURBO BARRA GOODNESS

STORY CARLY DALE PHOTOS NATHAN JACOBS

WARICK Meldrum is a purist's nightmare. The skilled-up larrikin is a massive fan of bolting turbocharged Barra donks between the rails of GM rides, which tends to work up certain keyboard warriors into full-blown hissy fits.

Warick's first offense was successfully campaigning his now 10.0-second Barra-powered VP Commodore at the 2017 Street Machine Drag Challenge. But then he upped the game by chucking the whole Barra shebang from that car into his dream ride: a 1967 SS Camaro.

I WANTED TO DO DRAG CHALLENGE IN MY CAMARO, AND THE BARRA DRIVELINE WAS THE ONLY ONE UP TO THE TASK, SO IT JUST MADE SENSE TO COMBINE THE TWO

Warick grabbed the keys to the factory, vinyl-roofed SS in April 2018. “I really wanted to do Drag Challenge 2018 in my Camaro, but didn’t have an engine and transmission that was up to the task other than the Barra driveline. So it just made sense to combine the two, he explains. “Plus, my mates and I reckoned that it’d be a hilarious combination that would upset the internet again – that made my decision pretty easy!” But it’s one thing to slide in the controversial turbo Ford sixcylinder for shits ’n’ giggles; fitting it properly and getting it running is another issue entirely.

“The timeframe was a little aggressive, with some serious allnighters to get it done, Warick explains. “On 20 August I said to my wife Casey: ‘I’m going into the shed and I’ll see you after Drag Challenge. And that is pretty much what happened!” Every weeknight, Warick would turn spanners and power the grinder from 9pm until 3am, with a few weekend stints for good measure. So, let’s just say his neighbours no longer give him a friendly wave.

Warick is a mechanic and auto-electrician by trade, but he’s self-taught at panel and paint. During those frantic two months, he bare-metalled the Camaro, before drowning it in Cortez Silver – twice. “I was set to repair a small rust spot under the edge of the vinyl roof, but the vinyl was that brittle that I had to remove it all, he says. “I then realised that I wasn’t happy with the entire paintjob. So I sprayed the Cortez Silver in my shed, but got crap stuck in the paint. I had to rub it all back again, and then hired a booth for the respray.

Next, the SS was relieved of its 350ci/TH350/10-bolt powertrain, before the Ford motor was pulled from Warick’s VP Commodore and wedged into one of America’s finest muscle cars.

I AM INTERESTED TO SEE IF ANYONE ELSE WILL DO THIS CONVERSION TO THEIR FIRST-GEN CAMARO, OR IF I’LL GO DOWN IN HISTORY AS THE ONLY ONE

The Barra combo consists of a Warick-built FG XR6 Turbo donk, paired with factory crank, cams and head, and finished with a horde sturdy components such as ARP bolts and studs, Spool conrods Ross Racing forged pistons. A Cummins Holset HX40 turbo fed 22psi into the mill at Drag Challenge via the stock manifold.

Bolted behind the custom Dellow bellhousing is the proven set-up a TH400 with transbrake and an SDE 3500rpm converter. The third member is a Commodore BorgWarner with a full spool, 3.45s and 31-spline axles.

Only a few minor adjustments were required for fitment. “Due to the engine height it was difficult to get the driveline angles correct, Warick explains. “I had to modify part of the sump to clear the steering arms, and also rework the subframe so as not to foul with the oil pick-up location. Haltech’s Elite Pro Plug-in ECU for Barra donks and closed-loop electronic boost control were the only other enhancements.

Warick first fired up the Barra Camaro a few weeks out from Drag Challenge, then spent the entire lead-up ironing out bugs; he was still tuning it at 3am on Monday of Day One.

“I’m stoked, the car went unreal on Drag Challenge, he says. “I got in it, did the whole event and got out of it, only checking the oil and water – that was it. With zero track time beforehand, it took three days of dialling in, but Warick finally sussed the tune at the end of Day Three. “I ran it at Swan Hill the next day and went 10.30@130mph on PULP, and ran similar on Friday, he says happily.

“It’s such a great feeling to build an entire car in that final timeslip at the end of Drag Challenge.

It'S by far the best car event in Australia and the best thing I’ve done Since Drag Challenge, Warick has whacked the Camaro ethanol and turned up the wick to 30psi, but we can’t tell you if it went any quicker. “I ran it at Heathcote and snapped the diff on the first run, he says. “I went home on the rear of a tow truck and haven’t been back since.

With the diff fixed, it’s now a matter of what’s next for this infamous driveline. “I only built the Barra-powered Camaro to do Drag Challenge, so everyone can just calm down now, Warick laughs.

“I never had any intention on keeping it that way, and the Camaro should be back to its V8 roots by the time everyone is reading this.

But I am interested to see if anyone else will do this conversion to their first-gen Camaro, or if I’ll go down in history as the only one with such a good sense of humour!” However, a new set of haters might need to get their crayons poised: “I just bought a VF Valiant rolling shell, and the driveline is going into that. If I make it to Drag Challenge this year then I would’ve competed three times in three different cars that all ran the same driveline, Warick says. “The combination is capable of so much and more, run which E85. is That why way the Valiant I can really will have lean all on of it!” the s ANDRA safety gear

ACING DC

WE HAVE a great video interview with Warick at Drag Challenge 2018 on our website, where he suggests that prospective DC entrants give themselves 12 months to build their car and get it done three months before the event to allow for plenty of testing. Does he heed his own advice? “That was for other people – not for me,” he laughs. “I hope to give myself a headstart for this year, as it’ll be a bit more serious, being ’caged.

hope I’ll get time to get it tech-inspected and test it first.” Head to whichcar.com.au/streetmachine to watch the video.

WARICK MELDRUM

1967 CAMAROSS

Paint: Cortez Silver

ENGINE

Brand: Ford Barra FG XR6

Turbo 4.0L

Manifold: FG Ford Turbo

Turbo: Cummins Holset

HX40

ECU; Haltech Barra Elite

Pro Plug-in

Head: Factory

Cam: Factory

Pistons: Ross Racing

forged

Crank: Factory; ACL Race

Series bearings

Conrods: Spool

Oil pump: Atomic;

modified sump

Fuel system: Bosch

1650cc injectors, Carter

Black pump, surge tank,dual Bosch 044s

Cooling: Camaro radiator, Saab thermos, Chinesemade 3in-core intercooler Exhaust: 3½in dump, 3in mandrel-bent system

Ignition: Factory

DRIVELINE Trans: TH400, manualised, reverse-pattern, transbrake Converter: SDE 3500rpm

Tailshaft: 3in,1330 unis

Bellhousing: Dellow Conversions

Diff: Commodore BorgWarner, full spool, 3.45:1 gears, 31-spline billet axles, 78 Series flange

SUSPENSION & BRAKES

Front: Hotchkis springs, Koni adjustable shocks

Rear: Viking coil-overs, triangulated four-link

Bushes: Nolathane

Steering: Strange closeratio box

Brakes: CPP C5 Corvette 330mm discs and calipers (f), HSV 285mm discs and PBR calipers (r)

Master cylinder: Wilwood

WHEELS & TYRES

Rims: Street Pro II Convo; 17x4.5 (f), 15x8 (r)

Rubber: M/T Sportsman S/R (f), M/T ET Street SS (r)

THANKS Some great Aussie businesses for all their help – SDE Converters, Bridgestone Select at Mornington, Tuff Mounts and Haltech; John Urquieta for his welding skills; my wife Casey and my kids Eva and Ivy for all their support